Fixing Sticky Clients: How to Improve Wi-Fi Roaming with Cisco Meraki

A sticky client is a laptop or phone that holds on to a distant access point instead of moving to the nearer one. The user sees full bars, then a frozen call as they walk. This is usually the device’s habit plus an AP layout that is too thin or too shouty — not “Meraki is broken.” Fix the number and position of APs first. Then ask for the dashboard roaming settings to be checked. Do not buy a new generation of radios only to hide a walk-the-floor problem.

Related pages: Cisco Meraki · High-density Wi-Fi: how many APs · How to choose the right Cisco / Meraki access point · Why Meraki Wi-Fi cannot print when the MX allows everything · Knowledge base

What is a sticky client, in one picture?

When moving around the office, the device would rather stay connected to a further access point than roam to a closer access point with stronger signal.

This is not a Meraki, Windows or iOS issue. Vendors implement this behaviour to prevent devices from excessive roaming.

How do you tell sticky roaming from a different fault?


Is this sticky roaming or something else?
What you see Likely cause Not the first fix
Walks the floor, call dies, then recovers on a new AP Sticky client / thin AP grid New Wi-Fi 7 SKU only
Same desk, always slow Client type, channel width, or 1G uplink Roaming toggle
Printing / file server fails, wired works SSID firewall (Deny Local LAN) Roaming
Only guests fail Guest policy, NAT, isolation Staff roaming profile
One model of scanner That device has no good roaming Do not retune the whole office around it without a test

What should you fix first?

Layout before knobs.

If two APs are 30 metres apart through concrete, no checkbox will make a laptop hop on time. Add or move an AP. If every AP is at full power, they all look “good enough” to a sticky NIC. Power and count belong together. That is the density article.

Then ask your partner to review:

Will Wi-Fi 7 or MLO end sticky clients?

No. Newer phones can hold more than one band at once, which helps stability. They can still prefer a far AP. A CW-917x in the same sparse grid as an old MR36 will present the same issues.

Buy Wi-Fi 7 when you are refreshing anyway. Do not buy it as a fix for roaming issues.

What does an administrator need when opening a roaming ticket?

That packet is enough to say “add an AP,” “turn down power,” or “this NIC will never roam well.”

FAQ

Can the access point force users to roam?

No. Roaming decisions are usually made by the device itself. An access point can be tuned so that a device prefers to roam, but it may not force a device to roam.

Should we turn 2.4 GHz off to force roaming?

Not as a first move. Scanners and older gear still need it. Prefer a staff SSID that uses 5/6 GHz well and keep 2.4 GHz for the devices that have no choice.

Can Meraki “kick” the client?

No, Meraki cannot autonomously “kick” the client to force it to roam. Meraki can be tuned such signal overlap is not excessive, so clients choose to roam by themselves.

Why is my signal low when sitting near the access point?

Check the access point the user is connected to. If the user is connected to a further access point when sitting close to a different one, you might have a sticky client.

Send the floor plan and the client model. Megatron Technology will say whether you are short of APs, over-powered, or dealing with a device that will not roam.

Request a roaming review: www.megatron.com.sg/ciscomeraki · Contact

Megatron Technology Pte Ltd (est. 1990, UEN 199002644W) is a Singapore Cisco Networking Partner and Managed Services Provider, and a Fortinet reseller. We design, size, licence, procure, deploy and support Cisco Meraki, FortiGate, and Cisco Catalyst & Data Centre from 2 Kallang Avenue #08-17 CT Hub, Singapore 339407.

Planning a Cisco Meraki deployment, refresh or renewal?

Megatron Technology is an authorised Cisco Networking Partner and Managed Services Provider in Singapore. Reach out to us for a quote if you need a price.

Request a quote
WhatsApp us Get a quote